ISDN PRI 2 port PCI & PCIe

Rate this item
(0 votes)

OpenVox D230 Series is now the leading 2 port T1/E1/J1 PCI-E card in the open source industry. It takes full advantage of Octasic® Hardware Echo Cancellation Module to deliver the superior voice quality over T1, E1, and J1 interface.

D230 Series is an upgrade product of the D210 Series. It’s supposed to be the most advanced 2 port T1/E1/J1 asterisk® card with superior quality in the open source community. The leading innovation ensures users to adjust the interrupts frequency to reduce the CPU load up to 70% and adjust the interrupt number to avoid interrupt number sharing or conflict.

D230 Series offers an on-board Octasic® DSP-based echo cancellation module. It supports T1, E1, and J1 environments and is selectable on a per-card or per-port basis. The Octasic® DSP-based EC module enables users to eliminate echo tails up to 128ms or 1024 taps across all 64 channels in E1 mode or 48 channels in T1/J1 modes. Further, this module takes advantage of the Octasic® Voice Quality Enhancement to provide superior sound quality on all calls.

D230 Series supports industry standard telephony and data protocols, including Primary Rate ISDN (both N. American and Standard Euro) protocol families for voice, PPP, Cisco, HDLC, and Frame Relay data modes. Both line-side and trunk-side interfaces are supported.

D230 Series works with Asterisk®, Elastix®, FreeSWITCH™, PBX in a Flash, trixbox®, Yate™ and IPPBX/IVR projects as well as other Open Source and proprietary PBX, Switch, IVR, and VoIP gateway applications.

Target Applications

    Voice-over Internet Protocol (VoIP) Services
    Complex IVR Trees
    "Meet-Me" Bridge Conferencing
    Calling Card Platforms
    VoIP Gateways (support SIP, H.323, and IAX)
    Legacy PBX/IVR Services
    Voice/Data Router (replace expensive routers)
    PRI/Switch Compatibility - Network or CPE

Minimum Hardware Requirement

    800-Mhz Pentium III
    128MB RAM

Operating Systems

    Linux (all versions, releases and distributions f rom 1.0 up)

Technical Specifications

    2 T1/E1/J1 ports with PCI interface for high performance voice and data applications
    RJ48 connector
    FPGA design, upgradeable firmware onsite
    Power Consumption: 2.3W Minimum, 3.5W Maximum at 3.3 V or 5 V.
    Operation temperature: 0°C to 50°C
    Dimension: 2U Form factor: 12*6.4*1.8cm

Optional Octasic® DSP Echo Cancellation Module—EC2064

    128ms tail/channel (on all channel densities)
    Octasic® Music Protection
    Adaptive Noise Reduction
    Automatic Level Control (G.169)
    Field upgradeable algorithm
    V.25 / V.8 answer tone (w/ and w/o phase reversal)
    DTMF as per Q.24
    No CPU load as a result of echo cancellation.
    Does not increase the physical size of the card, and no additional slot is required
    EC2064 power consumption: 0.33W/3.5W
    Storage temperature: -40°C to 75°C

PRI Switch Compatibility

    EuroISDN (PRI or PRA) - Q.931/Q.921
    Network or CPE
    AT&T 4ESS
    National ISDN 2
    CAS Voice Modes
    DMS 100
    Lucent 5E

Certifications

    RoHS Compliant
    Certificates: FCC, CE and CS-03

Read 73 times Last modified on Monday, 04 January 2021 20:51