Telecommunications equipment company and voip applications, Εταιρεία τηλεπικοινωνιακού εξοπλισμού και VoIP εφαρμογών

OpenVox D230 Series is now the leading 2 port T1/E1/J1 PCI-E card in the open source industry. It takes full advantage of Octasic® Hardware Echo Cancellation Module to deliver the superior voice quality over T1, E1, and J1 interface.

D230 Series is an upgrade product of the D210 Series. It’s supposed to be the most advanced 2 port T1/E1/J1 asterisk® card with superior quality in the open source community. The leading innovation ensures users to adjust the interrupts frequency to reduce the CPU load up to 70% and adjust the interrupt number to avoid interrupt number sharing or conflict.

D230 Series offers an on-board Octasic® DSP-based echo cancellation module. It supports T1, E1, and J1 environments and is selectable on a per-card or per-port basis. The Octasic® DSP-based EC module enables users to eliminate echo tails up to 128ms or 1024 taps across all 64 channels in E1 mode or 48 channels in T1/J1 modes. Further, this module takes advantage of the Octasic® Voice Quality Enhancement to provide superior sound quality on all calls.

D230 Series supports industry standard telephony and data protocols, including Primary Rate ISDN (both N. American and Standard Euro) protocol families for voice, PPP, Cisco, HDLC, and Frame Relay data modes. Both line-side and trunk-side interfaces are supported.

D230 Series works with Asterisk®, Elastix®, FreeSWITCH™, PBX in a Flash, trixbox®, Yate™ and IPPBX/IVR projects as well as other Open Source and proprietary PBX, Switch, IVR, and VoIP gateway applications.

Target Applications

    Voice-over Internet Protocol (VoIP) Services    Complex IVR Trees    "Meet-Me" Bridge Conferencing    Calling Card Platforms    VoIP Gateways (support SIP, H.323, and IAX)    Legacy PBX/IVR Services    Voice/Data Router (replace expensive routers)    PRI/Switch Compatibility - Network or CPE

Minimum Hardware Requirement

    800-Mhz Pentium III    128MB RAM

Operating Systems

    Linux (all versions, releases and distributions f rom 1.0 up)

Technical Specifications

    2 T1/E1/J1 ports with PCI interface for high performance voice and data applications    RJ48 connector    FPGA design, upgradeable firmware onsite    Power Consumption: 2.3W Minimum, 3.5W Maximum at 3.3 V or 5 V.    Operation temperature: 0°C to 50°C    Dimension: 2U Form factor: 12*6.4*1.8cm

Optional Octasic® DSP Echo Cancellation Module—EC2064

    128ms tail/channel (on all channel densities)    Octasic® Music Protection    Adaptive Noise Reduction    Automatic Level Control (G.169)    Field upgradeable algorithm    V.25 / V.8 answer tone (w/ and w/o phase reversal)    DTMF as per Q.24    No CPU load as a result of echo cancellation.    Does not increase the physical size of the card, and no additional slot is required    EC2064 power consumption: 0.33W/3.5W    Storage temperature: -40°C to 75°C

PRI Switch Compatibility

    EuroISDN (PRI or PRA) - Q.931/Q.921    Network or CPE    AT&T 4ESS    National ISDN 2    CAS Voice Modes    DMS 100    Lucent 5E

Certifications

    RoHS Compliant    Certificates: FCC, CE and CS-03

OpenVox D410 Series is the worldwide affordable single port T1/E1/J1 card and delivers the great voice quality over telephony systems. It supports up to 120 voice calls or 8.192 Mbps of full duplex data throughput over four T1, E1, or J1 lines. It takes full advantage of Octasic® Hardware Echo Cancellation Module.

The D410 Series offers an on-board Octasic® DSP-based echo cancellation module. It supports E1, T1 and J1 environments. It is selectable on a per-card or per-port basis. This feature enables signaling translation between E1 and T1 equipments and allows inexpensive T1 channel banks to connect with E1 circuits.The Octasic® DSP-based EC module enables users to eliminate echo tails up to 128ms or 1024 taps across all 128 channels in E1 mode or 96 channels in T1/J1 modes. Further, this module takes advantage of the Octasic® Voice Quality Enhancement to provide superior sound quality on all calls.

D410 Series supports industry standard telephony and data protocols, including Primary Rate ISDN (both N. American and Standard Euro) protocol families for voice, PPP, Cisco, HDLC, and Frame Relay data modes. Both line-side and trunk-side interfaces are supported.

D410 Series works with Asterisk®, Elastix®, FreeSWITCH™, PBX in a Flash, trixbox®, Yate™ and IPPBX/IVR projects as well as other Open Source and proprietary PBX, Switch, IVR, and VoIP gateway applications.

Target Applications

    Voice-over Internet Protocol (VoIP) Services    Complex IVR Trees    "Meet-Me" Bridge Conferencing    Calling Card Platforms    VoIP Gateways (support SIP, H.323, and IAX)    Legacy PBX/IVR Services    Voice/Data Router (replace expensive routers)    PRI/Switch Compatibility - Network or CPE

Minimum Hardware Requirement

    800-Mhz Pentium III    128MB RAM

Technical Specifications

    4 T1/E1/J1 port with PCI-Express interface for high performance voice and data applications    RJ48 connector

Certifications

    RoHS compliant    Certificates: FCC, CE and LVD

Operating Systems

    Linux (all versions, releases and distributions from 1.0 up)

PRI Switch Compatibility

    EuroISDN (PRI or PRA) - Q.931/Q.921    Network or CPE    AT&T 4ESS    National ISDN 2    CAS Voice Modes    DMS 100    Lucent 5E

Optional Octasic® DSP Echo Cancellation Module--EC100-128

    128ms tail/channel (on all channel densities)    Octasic®  Music Protection    Adaptive Noise Reduction    Automatic Level Control (G.169)    Field upgradeable algorithm    V.25 / V.8 answer tone (w/ and w/o phase reversal)    DTMF as per Q.24    No CPU load as a result of echo cancellation.    Does not increase the physical size of the card, and no additional slot is required    EC100-128 power consumption: 0.33W/3.5W    Storage temperature: -40°C to 75°C

OpenVox D210 Series takes full advantage of Octasic® Hardware Echo Cancellation Module to deliver the superior voice quality over T1, E1, and J1 in all 2 ports.

The D210 Series offers an on-board Octasic® DSP-based echo cancellation module. It supports T1, E1, and J1 environments and is selectable on a per-card or per-port basis. The Octasic® DSP-based EC module enables users to eliminate echo tails up to 128ms or 1024 taps across all 64 channels in E1 mode or 48 channels in T1/J1 modes. Further, this module takes advantage of the Octasic® Voice Quality Enhancement to provide superior sound quality on all calls.

D210 Series supports industry standard telephony and data protocols, including Primary Rate ISDN (both N. American and Standard Euro) protocol families for voice, PPP, Cisco, HDLC, and Frame Relay data modes. Both line-side and trunk-side interfaces are supported.

D210 Series works with Asterisk®, Elastix®, FreeSWITCH™, PBX in a Flash, trixbox®, Yate™ and IPPBX/IVR projects as well as other Open Source and proprietary PBX, Switch, IVR, and VoIP gateway applications.

Target Applications

    Voice-over Internet Protocol (VoIP) Services    Complex IVR Trees    "Meet-Me" Bridge Conferencing    Calling Card Platforms    VoIP Gateways (support SIP, H.323, and IAX)    Legacy PBX/IVR Services    Voice/Data Router (replace expensive routers)    PRI/Switch Compatibility - Network or CPE

Technical Specifications

    Two T1/E1/J1 ports with PCI interface for high performance voice and data applications    RJ48 connector    Power Consumption: 2.3W Minimum, 3.5W Maximum at 3.3 V or 5 V.    Operation temperature: 0°C to 50°C    Dimension: 12.9cm*10.3cm*2cm

Minimum Hardware Requirement

    800-Mhz Pentium III    128MB RAM

Certifications

    RoHS compliant    Certificates: FCC, CE and LVD

Optional Octasic® DSP Echo Cancellation Module--EC100-64

    128ms tail/channel (on all channel densities)    Octasic® Music Protection    Adaptive Noise Reduction    Automatic Level Control (G.169)    Field upgradeable algorithm    V.25 / V.8 answer tone (w/ and w/o phase reversal)    DTMF as per Q.24    No CPU load as a result of echo cancellation.    Does not increase the physical size of the card, and no additional slot is required    EC100-64 power consumption: 0.33W/3.5W    Storage temperature: -40°C to 75°C

PRI Switch Compatibility

    EuroISDN (PRI or PRA) - Q.931/Q.921    Network or CPE    AT&T 4ESS    National ISDN 2    CAS Voice Modes    DMS 100    Lucent 5E

Operating Systems

    Linux (all versions, releases and distributions from 1.0 up)